Ultra-Flexible 2-Core 0.15mm² Shielded Audio Cable – Professional Guitar & Microphone Signal Wire (Extra Soft PVC Jacket)

Are you tired of noisy cables that ruin your sound?

You are on stage. The lights are hot. You step on your distortion pedal. Suddenly, you hear it—a terrible buzzing sound. It is not your amp. It is not your guitar. It is your cable. Cheap cables act like antennas. They pick up radio signals, WiFi, and lights. They kill your tone.And then there is the stiffness. Some cables are so hard they fight you. You try to coil them up, and they spring back. You try to plug them into a tight pedalboard, and the jack hits the neighbor pedal. It is frustrating. You need a cable that works for you, not against you. You need a cable that is quiet, super flexible, and built to last. This is why we made our special 0.15 sq mm shielded cable.

What makes this cable different from the cheap ones?

Most cheap cables cut corners. They use steel or copper-clad aluminum wire. This is bad for audio. Steel has high resistance. It eats your signal. Your high notes get lost. Your bass gets muddy.Our cable uses pure copper conductors. We use oxygen-free copper (OFC) or high-purity bare copper. This means electricity flows easily. There is no traffic jam for your signal. You get a clean, crisp sound from your guitar or mic to your amp.But a good wire is not enough. You need a shield. Our cable has a special shield layer. It is usually an 85% copper spiral or a foil wrap. Think of this like a cage around your signal wire. It blocks outside noise. It stops RFI (Radio Frequency Interference) and EMI (Electromagnetic Interference). Whether you are in a club with dimmer lights or a room with fluorescent tubes, this cable stays quiet.

The “Extra Soft” Secret: Why flexibility matters

You see the words “Extra Soft” in the title. This is not just marketing. It is a real feature. Standard PVC jackets get hard in the cold. They crack if you bend them too much.We use a special PVC compound. It has a low memory. This means when you bend it, it stays bent. It does not spring back. This is huge for guitar players.

Perfect for Pedalboards

If you use a lot of effects pedals, you know the struggle. Space is tight. Our 0.13mm to 0.14mm fine copper strands make the cable very thin but strong. It fits into small jacks without forcing anything. You can snake it through a crowded board easily.

Great for Studio and Live

Cables get stepped on. Roadies throw them in trucks. A stiff cable will break inside after a few bends. Our flexible jacket absorbs the stress. It resists kinking. You can coil it up tightly for storage, and it won’t create permanent loops. It is also great for “drag chain” applications. If the cable needs to move back and forth (like on a robotic arm or a moving fader), it won’t break.

Technical Breakdown: Inside the Wire

Let’s look under the hood. We build this cable layer by layer to ensure performance.

The Conductor (The Heart)

• Structure: 2 Core (Dual Channel). This means two wires inside. One for the positive signal (+), one for the ground/return (-).
• Material: Bare Copper or Tinned Copper. Tinned copper resists oxidation better. It is great for humid environments.
• Gauge: 0.15 sq mm (approx 26-28 AWG). This is the sweet spot for low-current signals like microphones and guitar pickups. It is thick enough to carry the signal far, but thin enough to be flexible.
• Stranding: We use many thin strands (like 0.12mm or 0.10mm strands bunched together). More strands = more flexibility.

The Insulation (The Skin)

Each copper wire is covered in PVC or PE insulation. This keeps the two wires from touching. If they touch, you get a short circuit. No sound. The insulation color helps you identify the channels (e.g., Red for Right/Hot, Black or White for Left/Cold).

The Shield (The Armor)

This is the most important part for noise reduction.

• Type: Spiral Shield (Copper wire wound around) or Foil Shield (Aluminum foil).
• Coverage: 85% to 95% coverage. Higher is better. Our standard is 85% copper spiral. It is very effective against handling noise (the noise you hear when you rub the cable).
• Drain Wire: We include a bare copper drain wire. This makes grounding the shield easy during soldering.

The Jacket (The Coat)

• Material: Soft PVC.
• Features: RoHS compliant (safe for the environment), flame retardant, and oil resistant.
• Feel: It feels rubbery, not plastic-like. It grips well but slides easily through grommets.

Where should you use this cable?

This is a multi-purpose cable. It is not just for one thing. Here are the best places to use it:

Guitar and Bass Cables

This is the #1 use. The 0.15 sq mm size is perfect for instrument level signals. It is low capacitance. This preserves your high-end frequencies. Your tone stays bright. It is ideal for connecting your guitar to a pedal, or a pedal to an amp.

Microphone Cables (Low Z)

For dynamic microphones, you need a balanced line. Our 2-core shielded cable works perfectly for this. It carries the mic signal without picking up hum from stage lights. It is a great alternative to expensive bulk microphone cable.

Keyboard and Line Level

You can use it for synthesizers or mixing desk connections. If you need to connect a laptop to a speaker system (3.5mm to RCA or dual RCA), this wire is inside those cables.

DIY Projects

Are you a maker? Do you build your own pedals or cables? This bulk wire is perfect for you. It is easy to strip and solder. The soft jacket makes your finished product look and feel professional.

Specifications Table

Here are the hard numbers for our standard production run. We can customize these, but this is our “Gold Standard” spec:

Why buy imported style from us?

You might see “Japan import” or “Gold Kaneko” cables online. They are good, but they are expensive. We use the same manufacturing philosophy but at a better price.We focus on the “Drag Chain” concept. This comes from industrial automation (like robot arms). Cables in robots move millions of times. If they are stiff, they break. We apply this toughness to audio cables.Our quality control is strict. We test for:

1. Continuity: Every wire is tested to make sure current flows.
2. Shielding Coverage: We check that the shield covers at least 85% of the wire.
3. Jacket Adhesion: The outer skin must not peel off the shield.
4. Flex Test: We bend the cable 10,000 times to ensure it doesn’t crack.

You get a premium product without the premium brand markup. We are a factory. We sell direct to importers and brands.

Packaging and Shipping

We know how cables get damaged in shipping.

• Packing: Coils of 100m, 200m, or 500m.
• Packaging: Strong cartons or wooden pallets.
• Protection: Each coil is wrapped in plastic to stop moisture. We add desiccant packs if shipping to humid countries.
• Labels: We can print your brand logo on the coils or the cartons.

How to order and get samples?

Don’t just take our word for it. You need to touch it and hear it.Step 1: Request a SampleWe can send you a 5-meter or 10-meter sample roll. You can test the flexibility and the noise floor.Step 2: Check the SpecsTell us your specific needs. Do you need a 28 AWG for a thinner cable? Do you need a special white jacket for stage visibility? We can do it.Step 3: Get a QuotePrices change with copper prices (LME). We offer competitive FOB and CIF prices. We also support Alibaba Trade Assurance for safe payment.Ready to upgrade your cable lineup?Stop losing customers to noise and stiff cables. Give them the “Extra Soft” experience. They will thank you.Contact us today for the latest price list and free samples!